Land Pride RC4710 Rotary Mower

RC4710 — ROTARY CUTTER Land Pride's RC4710 / RCM4710 is a 10' offset version of our RC4715 Rotary Cutter.FEATURES AND BENFITS• Surpassed rugged industry standards — All Land Pride Rotary Cutters have been designed and tested and meet rigorous voluntary testing procedures according to ISO 4254-13.• Factory assembled — Arrives for quick and easy set-up. Minimal time wasted setting or prepping the unit.• 7 Year gearbox warranty — Shows confidence in gearbox integrity.• Rugged heavy built gearboxes — Capable of handling heavy cutting applications.• Gearbox seal protection — Gearbox bottom seal protection for longer bearing life.• Sliding guard for splitter gearbox — Sliding guard offers protection and easy access for improved efficiency of splitter gearbox maintenance.• 2 Piece driveline shields — Driveline grease zerks are easier to access.• Low hitch weight on tractor tongue — Ideal for smaller hp tractors by reducing the amount of weight on the drawbar.• Narrow A-frame hitch — Allows for a tighter turning radius.• Adjustable park jack angle — Park jack can be adjusted to be perpendicular to the ground.• Adjustable driveline hanger — Serves as support rest for the driveline when the cutter is unhooked from the tractor. Assist operator when attaching driveline to tractor power take-off shaft.• Input driveline: Cat. 6 CV — Driveline is matched just right for tractor capacity. Constant velocity (CV) U-joint allows for 80 degree turns without doing damage to the driveline.• Drivelines with slip-clutches: —o Cat. 4 intermediate o Cat. 4 or Cat. 5 wingso Driveline is sized right for the intended cutting capacity. Slip-clutches will slip under load to minimize twist damage to driveline profiles.• Grease zerks on end caps of driveline — Intermediate and wing driveline cross journals are easier to grease.• High blade tip speed — Allows clean cutting of material. • 6" (15 cm) Blade overlap — Eliminates skipping during turns.• Diamond blade bar — Provides the critical strength needed for consistent, top performance.• 3/16" (5mm) Round stump jumper — Standard thick stump jumper material keeps damage to a minimum.• Smooth top design — Reduces accumulation of debris and is easier and faster to clean.• Tops of decks are 100% welded— Makes center decks and wing decks stronger.• 1/4" (6 mm) Sidewall thickness — Increased thickness reduces damage from objects being thrown into deck sidewalls.• Multiple center skid shoe locations — Run two or four skid shoes in locations under the tongue pivots or out at the wing hinges.• Beveled skid shoes on wings — Reduces gouging the ground when turning.• LED signal lights — LED lights are bright, long lasting, and resist vibration, unlike incandescent lights.• Hinged wing sections — Allows cutter to follow terrain. Ideal for rough ground where hillsides, ditches, and hollows can cause uneven cutting.• 1" (2.5 cm) Solid hinge rods — Larger diameter hinge rod provides greater strength in the hinge area.• Wing transport lock pins —Transport lock pins will hold wings in folded position in the event of hydraulic loss.• Enclosed dual 1" leveling rods — Cutter pulls equally on the rear axle while traveling over rough terrain.• 5-Bolt hubs — 5-Bolt hubs make the wheel assembly more durable and longer lasting.• Drain holes in wheel rims — Allows water to drain from wheels mounted on folded-up wings. Helps prevent paint deterioration and rusting to the wheel rims.• Spring cushioned center-axle — Protects unit from bumps and ground shock.• Optional spring cushioned wing-axles— Further improves ride over a multitude of terrains.• Replaceable individual wheel spindles — Spindles can be replaced when damaged without replacing entire axle assembly.• Wheel options —o Laminated tires: Eliminates flats.o Air-filled tires: Give better cushion while transporting.o Foam-filled tires: Give better cushion while transporting and can’t go flat.• LP Performance hitch option — Great for uneven terrain, reduces drawbar wear. Hitch pivots freely up and down and pivots about the tractor drawbar up to 12 degrees in both left and right directions.• Bar-tite hitch option — Ideal for extreme conditions. Clamps tight to drawbar eliminating drawbar wear.• Maintenance free tongue & axle pivots — Self-lubricating journal bearings make for less maintenance.• Color coded hydraulic hose handles — Easy hose identification & sturdy handle to easily connect & disconnect from tractor.• 4 lip, metal backed wheel hub seal with purging capabilities — Seals make it harder for water & debris to enter the hub and grease to leave the hub. Metal backing prevents sticks and twine from destroying the seal lips. Greaseable cast steel, continuous hinges Cast steel hinges make a strong connection & are easy to lubricate.• Center axle options —o Single suspension center axle: Spring cushion at the cylinder for cushion with least amount of moving partso Independent suspension center axle: Offers additional suspension support per wheel axle.o Walking tandem center axle: Designed for versatility over a multitude of terrains.o Parallel pivot center axis: provides unmatched ground contact for hill-like terrains.• Wing axle option —o Solid wing axle: One piece wing axle that attains support from cylinder spring cushion on center axle.o Independent suspension wing axle: Offers additional suspension support on wing axle.• Dual-acting fold cylinders (optional) — Allows for a narrow transport width of 7'3" (2.21 m).• Stroke control flip spacers — Easily change cut height with a flip of a spacer.• SMV Mounting Socket (Standard)— SMV mounting socket receives most SMV signs equipped with a mounting blade for ease of attachment and removal when transporting on a truck or trailer. • SMV Sign (Accessory) — SMV sign is offered as an accessory when the tractor’s SMV sign and mounting blade does not fit the cutter’s standard SMV mounting socket.GEARBOX WARRANTY7 Year Limited Gearbox Warranty shows confidence in gearbox integrity. (Years 6 & 7 parts only.)4" CUTTING CAPACITYThese cutters offers 4" cutting capacity. See Operator's Manual for more information.OPTIONAL LP PERFORMANCE HITCHClevis swivels two ways: Cutter can swivel clockwise and counterclockwise about tractor drawbar up to 12° in either direction.ADJUSTABLE JACK ANGLEHelps keep park jack vertical when in use.LED SIGNAL LIGHTSLED lights are bright, long lasting and resistant to vibration, unlike the incandescent lights.BEVELED SKID SHOESWing skid shoes are flanged up along length of outside edge. This allows operator to turn without leading edge of wing skid shoes digging into the ground.SLIDING GUARDEasy-off shields and a patented sliding guard over the splitter gearbox make maintenance easy to perform.DIAMOND BLADE BARForged diamond blade bar provides strength where it's needed most.SPRING CUSHIONED AXLESSpring cushioned axles improve ride and are available options on both center and wing axles.Similar models may be shown in addition to the featured model. Equipment may be shown with options. Specifications are subject to change without prior notice.