Land Pride RCBM5710 Rotary Mower

RCBM5710 — ROTARY CUTTERThe RCB5710 Rotary Cutters are single wing mowers that are ideal for roadside mowing. The left-hand wing is replaced with a weight box on the RCB and the right-hand wing is replaced with a weight box on the RCBML models. This allows the operator to travel next to the road’s shoulder, remaining on more level ground. All the features you love from our 15-foot cutters are there too, in a 10-foot single wing model!FEATURES• Surpassed rugged industry standards. All Land Pride Rotary Cutters have been designed and tested and meet rigorous voluntary testing procedures according to ISO 4254-13.• Factory assembled Arrives for quick and easy set-up. Minimal time wasted setting or prepping the unit.• Seven Year limited gearbox warranty. Shows confidence in gearbox integrity.• Rugged heavy built gearboxes. Capable of handling heavy cutting applications.• Gearbox seal protection. Gearbox bottom seal protection for longer bearing life.• Sliding guard for splitter gearbox. Sliding guard offers protection and easy access for improved efficiency of splitter gearbox maintenance.• Detachable shield on the wing gearbox. Provides easy maintenance access to the driveline slip clutch and yoke.• Two piece driveline shields. Driveline grease zerks are easier to access.• Low hitch weight on tractor drawbar. Ideal for smaller hp tractors by reducing the amount of weight on the drawbar.• Narrow A-frame tongue. Allows for a tighter turning radius.• Adjustable park jack angle. Park jack can be adjusted to be perpendicular to the ground.• Adjustable driveline support. Serves as support rest for the driveline when the cutter is unhooked from the tractor. Assist operator when attaching driveline to the tractor power take-off shaft.• Input driveline: Cat. 6 CV. Driveline is matched just right for tractor capacity. Constant velocity (CV) U-joint allows for 80 degree turns without doing damage to the driveline.• Drivelines with slip-clutches: Cat. 5 intermediate Cat. 4 or Cat. 5 wing. Driveline is sized right for the intended cutting capacity. Slip-clutches will slip under load to minimize twist damage to driveline profiles.• Grease zerks on end caps of driveline. Intermediate and wing driveline cross journals are easier to grease.• High blade tip speed. Allows clean cutting of material. • 6" Blade overlap. Eliminates skipping during turns.• Forged blade bar (Optional). Provides the critical strength needed for consistent, top performance.• 3/16" Round stump jumper (Optional). Standard thick stump jumper material keeps damage to a minimum.• Smooth top design. Reduces accumulation of debris and is easier and faster to clean.• Tops of decks are 100% welded. Makes center and wing decks stronger.• Deck ArmorTM (Optional). Reduces deck damage from blade to deck contact without affecting cut quality.• Replaceable 1/4" side skirt thickness. Increased thickness reduces damage from objects thrown into the side skirt.• Multiple center skid shoe locations. Run two skid shoes under the hitch pivots or two skid shoes under the wing hinges.• Beveled skid shoes on the wing & weight box. Reduces gouging the ground when turning.• LED signal lights. LED lights are bright, long lasting, and resist vibration, unlike incandescent lights.• Wire harness 7-pin plug holder. Spring hose loop mounted holder keeps wire harness plug out of the dirt and rain.• Hinged wing section. Allows the cutter to follow the terrain. Ideal for rough ground where hillsides, ditches, and hollows can cause uneven cutting.• 1" Solid hinge rods. Larger diameter hinge rod provides greater strength in the hinge area.• Wing transport lock pin. Transport lock pin holds the wing in the folded position in the event of hydraulic loss.• Enclosed dual 1" leveling rods. Cutter pulls equally on the rear axle while traveling over rough terrain.• Five-bolt hubs with larger bearings, five lip hub seals, and bolted-on hub caps. Makes the wheel assembly more durable and longer lasting. Five hub seals make it harder for water & debris to enter the hub and grease to leave the hub. Hub caps cannot be knocked off by foreign material.• Drain holes in wheel rims. Allows water to drain from wheels mounted on the folded-up wing. Helps prevent paint deterioration and rusting to the wheel rims.• Replaceable individual wheel spindles. Spindles can be replaced when damaged without replacing entire axle assembly.• Wheel options. Laminated tires: Eliminates flats. Air-filled tires: Give better cushion while transporting.• Foam-filled tires: Give better cushion while transporting and can’t go flat.• LP Performance HitchTM (Optional). One person Hook-up. Great for uneven terrain, reduces drawbar wear. Hitch pivots freely up and down and pivots about the tractor drawbar up to 12 degrees in both left and right directions.• Bar-Tite hitch (Optional). Ideal for extreme conditions. Clamps tight to drawbar eliminating drawbar wear.• Maintenance free tongue & axle pivots. Self lubricating journal bearings make for less maintenance.• Color-coded hydraulic hose handles. Easy hose identification & sturdy handle to easily connect & disconnect from tractor.• Hydraulic hose holders. Tongue mounted hose holder keeps hose tips out of the dirt.• Greaseable cast steel, continuous hinges. Cast steel hinges make a strong connection & are easy to lubricate.• Center axle options. HD Single suspension center axle: Spring cushion at the cylinder for cushion with least amount of moving parts. Independent suspension wing axles: Offers additional suspension support on the wing axle. Walking tandem center axle: Designed for versatility over a multitude of terrains. Parallel pivot center axle: Provides unmatched ground contact for hill-like terrains.• Wing axle option. Independent suspension wing axle: Offers additional suspension support on the wing axle. Walking tandem wing axle: Designed for versatility over a multitude of terrains. Parallel pivot axle: Provides unmatched ground contact for hill-like terrains.• Dual-acting fold cylinder (Optional). Allows for a narrow transport width of 7'-3" (2.21 m).• Flip spacers. Easily change cut height with a flip of a spacer.• SMV Mounting Socket (Standard). SMV mounting socket receives most SMV signs equipped with a mounting blade for ease of attachment and removal when transporting on a truck or trailer. • SMV Sign (Accessory). SMV sign is offered as an accessory when the tractor’s SMV sign and mounting blade does not fit the cutter’s standard SMV mounting socket.Similar models may be shown in addition to the featured model. Equipment may be shown with options. Specifications are subject to change without prior notice.